Unit sizing and supply
We calculate flow rate and temperature rise for your fixtures, then supply the correctly sized gas or electric unit. You are not guessing at BTU ratings or buying a box store model that is wrong for the house.
Every quote covers the full mechanical install, not a partial job that leaves you hiring someone else to finish. Here is what is standard and what we price separately when your home needs it.
We calculate flow rate and temperature rise for your fixtures, then supply the correctly sized gas or electric unit. You are not guessing at BTU ratings or buying a box store model that is wrong for the house.
We run the dedicated gas line or 240-volt circuit the unit requires, including resizing to 3/4-inch gas pipe or adding a breaker and disconnect. Panel upgrades are quoted upfront if your service cannot carry the load.
We install the stainless or PVC vent to manufacturer spec and route condensate to a drain or neutralizer. Short or improperly pitched vents are the number one cause of tankless faults, so we build it right.
We cut and fit copper pipe or PEX tubing, install isolation and descaling valves, and pressure-test every joint. Those valves make future maintenance a 30-minute job instead of a teardown.
We pull the Prince George's County mechanical permit and meet the inspector on site. You get the signed-off paperwork for your records and for resale.
We drain and haul away the old tank, sweep the area, and leave the closet cleaner than we found it. No leftover parts in your garage.
Tankless water heater installation Bowie MD is the trade of replacing a storage-tank water heater with a wall-mounted on-demand unit that heats water only when a fixture calls for it. The job is never just swapping boxes. We size the unit to your fixture load in gallons per minute, run a dedicated gas line or 240-volt circuit, cut and solder copper pipe or crimp PEX tubing to the new connections, install the stainless vent, and pressure-test the whole assembly before the drywall goes back. A 199,000 BTU condensing unit and a 9.5 GPM electric model need completely different prep, and we spec both.
Most Bowie homes we walk into have a 40- or 50-gallon tank in the garage or utility closet that is 10 to 15 years old, and the homeowner is tired of reheating the same water. If you have been searching tankless water heater installation Bowie MD near me because the tank is leaking or your teenagers empty the supply every morning, the fix is a properly sized unit, not a bigger tank. We also handle tankless water heater conversion Bowie MD projects where a gas line has to be upsized from 1/2-inch to 3/4-inch to feed the burner.
You get a written scope, a firm price, and a clean job site. Here is what the five stages look like from your side of the door.
Schedule
Call or book online — a real human picks up and confirms a 2-hour arrival window.
Diagnose
Licensed tech inspects on-site, then walks you through the cause and your options.
Fix
The job is completed to code and done right the first time — no shortcuts, no surprises.
Guarantee
Every job backed by a written workmanship warranty — and we stand behind it.
Press tool and soldering torch
For copper pipe connections. Press fittings speed up the work and reduce open-flame risk in tight closets; soldered joints are used where code or access requires.
Tube cutter and pipe wrench
Clean square cuts on copper and precise tightening on gas and water fittings. A burred cut is a leak waiting to happen.
Pressure gauge
We pressure-test gas and water lines before and after the install to confirm every joint holds at code pressure.
Leak detection equipment
Electronic and soap-solution testing on gas connections and supply lines, so nothing is left to a sniff test.
Multimeter and circuit tester
For electric tankless installs, we verify voltage, breaker sizing, and grounding before the unit is energized.
Manual J-style load sizing
We count fixtures, measure flow rates in gallons per minute, and calculate temperature rise from incoming groundwater temperature. That math determines the unit size, not a guess based on square footage.
Gas line sizing per code
We measure run length and BTU demand, then size the gas pipe to code so the burner gets full pressure under load. Undersized gas lines cause ignition faults and short unit life.
Manufacturer vent spec
Every tankless unit has a required vent length, diameter, and pitch. We follow the installation manual exactly, because vent shortcuts are the top cause of warranty denials.
Pressure and flow testing
After install we run hot water at every fixture, check temperature at the tap, and confirm flow holds. If a fixture underperforms, we find out before we leave.
01
What we do: We sized a 199,000 BTU condensing gas unit, upsized the gas line to 3/4-inch, and installed a stainless vent through the garage wall. Install took one day.
→ Endless hot water for four showers in a row, and the old tank hauled away the same afternoon.
02
What we do: We ran a load calculation, upgraded the panel to 200 amps, and installed a 240-volt electric tankless unit with a dedicated 60-amp circuit and disconnect.
→ Reliable hot water without gas, and panel capacity for future additions.
03
What we do: We mounted a compact outdoor-rated tankless unit on the exterior wall, ran the gas and water lines through the rim joist, and insulated the penetrations.
→ The closet became storage space, and the homeowner gained a full shelf they did not have before.
04
What we do: We shut off the supply, contained the water, and installed a replacement tankless unit the next morning with a temporary inspection sign-off.
→ Hot water restored in under 24 hours, with the county inspection completed the following week.
Bowie housing stock ranges from 1960s split-levels in Old Bowie to newer builds in Woodmore and Enfield Chase, and the plumbing reflects that spread. Older homes often have 1/2-inch gas service that cannot feed a 199,000 BTU tankless burner, so we upsize to 3/4-inch as part of the job. Newer homes with PEX manifolds need different connection methods than copper. Winters here drop into the teens, which raises the temperature rise the unit must handle and makes freeze protection on exterior-mounted units non-negotiable. We pull mechanical permits through Prince George's County and meet the inspector on site, and we know which neighborhoods have the panel capacity for electric tankless water heater install Bowie Maryland without an upgrade. If you are comparing tankless vs tank water heater cost Bowie MD, we will run the numbers for your specific house, not a generic chart.
Old Bowie
Older cottages and split-levels often have 1/2-inch gas lines and tight utility closets, so gas line upsizing and wall-hung mounting are common.
Belair at Bowie
Mid-century homes with garage-mounted tanks and copper supply lines. We check for corrosion at the shutoff valves before connecting a new unit.
Woodmore
Newer construction with PEX manifolds and 200-amp panels, which makes electric tankless and dedicated circuit installs straightforward.
Pointer Ridge
Utility closets are shallow in many floor plans, so compact or outdoor-rated units are often the right fit.
Tulip Grove
Family-sized homes with high hot-water demand. We size for simultaneous showers and laundry, not just fixture count.
Cold winter groundwater temperatures
Incoming water in January can be 45 to 50 degrees, which means the unit must raise temperature 70 degrees or more. We size for winter conditions, not summer averages.
Older 1/2-inch gas service
Many pre-1980 homes cannot feed a high-BTU tankless burner without a gas line upgrade. We include that in the quote when we see it.
Exterior wall mounting
Units mounted on exterior walls need freeze protection and insulated penetrations. We install heat tape and backflow prevention where required.
Most calls start with a symptom the homeowner has lived with too long. These are the four we hear most in Bowie.
Problem
A 40-gallon tank cannot keep up with three showers and a dishwasher. The last person in gets a cold surprise, and the tank runs constantly trying to recover.
Our Fix
We size a tankless unit to your actual fixture load so hot water never runs out. A 199,000 BTU gas unit delivers continuous supply at 9 to 11 GPM, enough for simultaneous showers and appliances.
Problem
A leaking tank can flood a garage or closet and damage flooring and stored belongings. Once the tank shell rusts through, repair is not an option.
Our Fix
We drain and remove the failed tank, inspect the surrounding supply lines for corrosion, and install a wall-hung tankless unit that eliminates the tank failure risk entirely.
Problem
Older Bowie homes often have tight utility spaces. A new 50-gallon tank may not fit, and a tank in a cramped closet is hard to service.
Our Fix
A tankless unit mounts on the wall and takes about 18 by 24 inches. That frees the floor space and makes service access easy, which matters in Belair at Bowie and Pointer Ridge layouts.
Problem
A storage tank keeps water hot 24 hours a day, even when nobody is home. That standby loss shows up on every bill and gets worse as the tank ages.
Our Fix
Tankless heats only when a fixture calls for water. For a family of four, the reduction in standby loss is measurable within the first billing cycle after install.
A tankless unit changes how your house uses hot water and how much floor space it gives back. These are the four outcomes our customers notice first.
Endless hot water
A correctly sized unit delivers hot water at 2 to 11 gallons per minute continuously, so back-to-back showers, a running dishwasher, and the laundry don't fight each other. No recovery time, no waiting 30 minutes for the tank to catch up after the last person showers.
Lower standby losses
A storage tank keeps 40 to 80 gallons hot around the clock, even when nobody is home. Tankless heats on demand, which cuts standby heat loss and can trim water-heating energy use. For a Bowie household of four, that difference shows up on the monthly gas or electric bill.
Frees up floor space
A wall-hung unit is roughly 18 by 24 inches and about 8 inches deep. That returns a full closet or garage corner you were losing to a tank. In Belair at Bowie and Tulip Grove homes where the utility closet is tight, that reclaimed square footage is often the reason homeowners call.
Longer service life
Tankless units typically last 20 years with annual descaling, against 8 to 12 for a tank. Fewer replacements over time is the real cost story, and it is why tankless vs tank water heater cost Bowie MD comparisons favor tankless past the 12-year mark.
Typical 2026 pricing for tankless water heater installation Bowie MD runs $2,800 to $6,500 installed, depending on unit size, vent length, and whether the gas line or electrical panel needs work. A straightforward garage swap with an existing 3/4-inch gas line lands near the low end. Long vent runs, a panel upgrade, or a gas line resize push it higher. We quote the full job upfront, permit included, so the number you hear is the number you pay.
Typical Investment Range
$2,800 - $6,500 depending on scope
A tankless unit lasts about 20 years against 8 to 12 for a tank, and it cuts standby heat loss every month. Spread over its life, the installed cost is often lower than two tank replacements.
What changes the price
Unit size and type
A 199,000 BTU condensing gas unit costs more than a smaller non-condensing model, and electric units vary by kW rating. Sizing to your fixture load determines which unit you need.
Gas line or panel work
Upsizing from 1/2-inch to 3/4-inch gas pipe or adding a 240-volt circuit and breaker adds labor and materials. We identify this during the assessment, not after the wall opens.
Vent length and routing
A short direct vent through a garage wall is cheaper than a long run through a finished ceiling. Vent length and material affect both cost and performance.
Permit and inspection
Prince George's County requires a mechanical permit and inspection. We include the permit fee and inspection coordination in every quote.
Old unit removal
Draining and hauling away the old tank is included. If the old unit is in a crawlspace or attic with limited access, removal takes longer and affects labor.
Google ★★★★★4.9
They measured our gas line and counted fixtures before quoting, which no one else did. Install was clean, the permit was pulled, and the inspector signed off. Hot water has not run out once since.
Yelp ★★★★★4.8
Our tank failed on a Friday and they had a tankless unit running by Saturday morning. Fair price, no upsell, and they hauled the old tank away. The descaling valve they added makes maintenance easy.
BBB ★★★★★4.9
We needed a panel upgrade for electric tankless and they handled it without juggling subcontractors. The quote was firm and the work passed inspection first time. Two years in, zero issues.
Tankless work punishes shortcuts. A unit that is undersized, vented short, or fed by an undersized gas line will throw ignition faults and cold-water slugs for years. Our technicians hold Maryland State Plumbing License credentials and WSSC Licensed Plumber standing, and we install Rheem, Navien, Rinnai, and A.O. Smith units to manufacturer spec and local code. We have converted everything from 1970s Bowie split-levels with 1/2-inch gas stubs to newer Woodmore builds with PEX manifolds, and we know which vent kits and condensate handling each one needs.
Real experiences from customers who chose our Tankless Water Heater Installation services.
“Our 50-gallon tank was 14 years old and we were down to two showers before cold water. The crew sized a Navien unit, upsized the gas line, and had hot water running the same afternoon. They pulled the permit and the inspector signed off a few days later. Clean work, no surprises on the bill.”
Marcus T.
Homeowner, Belair at Bowie
“I called three plumbers about tankless water heater installation Bowie MD and only this one actually measured the gas line and counted fixtures. The quote was higher than the phone estimates but it was the real number. Install took about six hours, they hauled the old tank away, and my electric bill dropped the next month.”
Denise R.
Homeowner, Tulip Grove
“We wanted electric tankless but the panel could not carry it. They walked me through the load calculation, upgraded the panel, and installed a unit that keeps up with four people. The descaling valve they added makes maintenance easy. Two years in, zero issues.”
Raymond K.
Homeowner, Woodmore
Real answers to the questions we hear most often from local homeowners and property managers.
A tank that lets go at 2 a.m. is an emergency. We shut off the supply, contain the water, and get you on the schedule for tankless water heater replacement Bowie MD the same week.
View Emergency PlumbingSediment from an aging tank can foul fixtures and aerators. When we install a new tankless unit, we can clear the lines and check flow at every drain so the hot water actually reaches the tap.
View Drain CleaningNot every failing unit needs replacement. If your existing tankless unit is throwing error codes or losing temperature, we diagnose it first and only recommend a swap when repair no longer makes sense.
View Water Heater RepairIf tankless is not the right fit for your home or budget, we install and replace standard tank units too. We will tell you honestly which option fits your household and your gas or electrical setup.
View Water Heater InstallationBefore we hang a new unit, we check the surrounding supply lines and shutoff valves for hidden leaks. Finding a slab leak or a weeping joint now saves you from tearing into a finished wall later.
View Leak DetectionFrozen pipes in older Bowie homes can split a line behind the wall. We repair the burst section and pressure-test the run before connecting your new tankless unit to it.
View Burst Pipe RepairCall us at +1 (831) 293-1204 for same-day service or to schedule a visit. We answer the phone 24/7 for emergencies and return messages within one business day for non-urgent requests. Our office is in Bowie, Maryland, and we serve all of Prince George's County.
Phone
+1 (831) 293-1204Address
16704 Melford Blvd #400, Bowie, MD 20715
Hours
Mon–Fri: 7AM – 7PM
Sat: 8AM – 4PM
Sun: Emergency Only
24/7 Emergency Available